How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Right here in the next paragraph you will find a lot of amazing insights about Tools You Need to Install a New Bathtub .
Mounting a bathtub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately tough task. If the old tub is conveniently accessible, the project can relocate easily; if you have to open a wall surface to remove the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to move out the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is far better to consider utilizing one prior to you start. Chances are you might require a specialist plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have already purchased a new tub as well as don't require to transform the plan of your previous water system pipelines.
Your devices and also product list should comprise the following:
Preparing for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the faucets device to stop pressure on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last setting.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The process of removing the existing faucets can be quite bothersome because of the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bathtub
Utilizing both wooden boards under its feet, put the bathtub in the needed placement. The wood boards are useful in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following goal is to guarantee that the bath tub is leveled all round. This can be achieved by inspecting the level and also adjusting the feet on the tub till the spirit level checks out degree.
To mount taps, fit the bottom of the outermost adaptable tap port to the proper supply pipeline by making a compression join; then do the exact same for the various other faucet.
Switch on the supply of water as well as examine all joints and also new pipework for leaks as well as tighten them if essential. Fill the bathtub and likewise examine the overflow electrical outlet and the normal outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the tub must wait till the bath tub has actually been used at least once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will call for reducing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location between the tap and the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with typical tap ports. The former kind needs to be attached to the faucet ends first, tightening up only by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to split a stiff seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to difficulties with wetness as well as possible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water prior to sealing, to permit the motion experienced when the tub remains in usage. The sealant can fracture relatively very early if you do not take into consideration this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I discovered that blog posting on Installing A Bathtub while perusing the web. Sharing is caring. Helping people is fun. Thank-you for taking the time to read it.
Quote & Schedule Report this page